How to install a utility sink next to the washer?


The presence of a utility sink next to the washer can help you in performing various washing tasks. In this Guide, we will Follow the Instructions about How to install a utility sink next to the washer. Further selecting the best utility sink next to the washer can elevate the overall look of your launder room.

But how to install a utility sink next to the washer is a basic question. We have prepared a list of instructions to help you in installing a utility sink.

Steps to install a utility sink next to the washer

Following are some basic tools that you need while installing a utility sink. If you want to purchase a new kitchen sink, then click here.


  • Pliers
  • Wrench 
  • Hammer
  • Pipe splitter 
  • Measuring tape
  • Plumber glue and tape
  • Utility knife o Pipe cutter
  • PVC Y-fitting and hand saw

Step 1


The first step is all about measurement. You will have to measure the height of the drain pipe from the ground level to adjust the height of the sink.

For this purpose, before starting any of your plumbing tasks you will have to turn off the main water supply to avoid any possible mess.

After turning off the water supply, take a measuring stick to measure the height of the drain pipe. Starting from the ground level to the position of the sink’s placement. Further, figure out where or at what point the prior washer’s drain line goes down.

Now you have to make a second measurement by using the initial sink’s drain line measurement. By using this measure is meant to mark measurable signs on your washer’s drain line.

This measurement is done to specify the exact location where you will install your new Y-fitting detach both drain lines from one another. Click here for Best Kitchen Faucets.

Step 2 

Cutting the Prior Drain Pipe

For the second step, you will have to cut the drainpipe at that specific point where you marked on the venting pipe that will connect above it.

To transport water towards the downward drain pipe you will have to create a horizontal T- fitting by cutting the pipe.

After completing the cutting process, use your Deburring tool to soften the inner side of the pipe. It is very important to Deburr the inner side of the pipe as the rough surface will create problems during the next attachment process. Click Here for Touchless Faucets.

Step 3

Attachment Process 

The attachment stage is very sensitive. You will have to understand this process carefully. A minor mistake during the attachment process can cause dripping and leakage issues.

Attach the available Y-fitting with the drainpipe. In such a position that the top end of Y-fitting should attach to the vent pipe.

Carefully attach both openings of Y-fitting at their appropriate place. Such as attaching one arm Y with the horizontal flow in the direction of the current washer’s drain and the other arm Y should be attached to the utility sink drain pipe. I hope this article will help you with How to install a utility sink next to the washer

After all the attachment process is done now you will have to firmly apply plumbing glue or thread at every connection so that issues like dripping may occur.

Ignorance of minor leakage could also cause severe damage in the future. So make sure all ends are made secure. Click Here for pullout faucets.

Step 4

Locate Available Water Sources

By following the above three basic steps the drain is placed in its right position. Now during our fourth step, we will similarly locate the water sources.

Track both hot and cold water line connections near the washer. After tracking both connections at their accurate place, disconnect the water pipe to place both hot and cold water pipes.

If your water pipe does not have any joint, you will have to cut your water pipe. Even though if the main water supply is off you will need a bucket to gather the available water standing in the line during the cutting process. Cut the water pipe.

This cut must be somewhere between both washer and sink. 

Step 5 

Install Hot and Cold Water supply lines

For installing both hot and cold water supply lines use a two-headed brass pipe, install this brass pipe splitter on the main water pipe by using a screw.

Firmly screw the splitter by making sure none of the ends has remained unsecure. Further to assure the tightness of connection using a wrench.

This separation between hot and cold water pipes is very beneficial. As the water supply lines are separated one line will flow towards while the other towards the washer.

As soon as the splitter is firmly attached reconnect the pipes with the washer. For reconnecting use Plier and wrench.

Step 6

Connect Hoses, Lines

Measure the length of the required tube to reach the sink. Attach the tube for both hot and cold water supply lines. Both tubes must be of different colors to distinguish between hot and cold water.

Such as using a red tube to indicate hot water whereas using the blue tube for indicating cold water. Use wrenches and tools to tighten the connection properly in an appropriate way. 

Step 7

Final Step 

The final step is all about connecting the new flexible tubes with the utility sink: both hot and cold water supply lines.

After you have completed all the work, check at once all the connections properly whether they are secure or not. Now you can turn on the main water supply line.

For making any further changes in the future, you will have to turn off the main water supply lines to avoid splashing.

 Installing a laundry room faucet 


  • Pliers
  • Pipe wrench 
  • Flashlight
  • Plumbers tape
  • Nuts
  • Gaskets

Step 1

Turn off Water

Turn off the main water supply line. To avoid any possible mess or water wastage. 

Step 2

Place The Faucet 

Place the faucet in the sinkhole. Every sink already has a pre-drilled hole for the placement of the faucet. Whenever you purchase a faucet you have noticed some tools and nuts are provided with the faucet to fix it.

Check the box there will be a rubber gasket and required nuts. To fix the faucet properly use them.

Step 3

Tighten The Nuts 

Once you have placed the faucet over the sink with providing nuts. Tighten those nuts firmly. While tightening the nuts be sure to tighten them beneath the sink with the help of a wrench.

If you have used plumbers putty, it can emerge at the side due to excessive tightening. You can easily clean it off with the help of a damp towel or knife.

Step 4

Connect Hot and Cold Water Lines 

If you want to use both hot and cold supply lines. Make sure your faucet must support this function. Take the hot and cold water supply lines and fix them with the faucet in their appropriate position.

So that the faucet handles can perform their respective work. Seal the connections properly using a wrench or your hand itself.

Final step

Check all the Connections 

The final step is all about checking all of your connections properly. Turn on the water supply to check whether there is any leakage or loose connection. In case of such a situation fix the issue.

The area under the faucet must be secured properly. Minor leakage could cause problems like rusting, cracking, or tarnishing. Use a flashlight to confirm everything is ok. After all, work has turned on the water supply line.


What problems does a utility sink solve if you install it next to the washer?

How to install a utility sink next to a washer the Complete Guide is here Installing a utility sink next to a washer can solve various problems. One of the major problems like mess created during the shifting of cloths from the waster to sink can be reduced.

Further, some of the clothes are very heavy to carry. It requires a lot of effort in carrying them if you are How to install utility sink next to washer sink is away from the washer.

By placing or installing the utility sink beside the sink can reduce the problem of weight. You can easily carry the clothes from one side and place them easily over the sink.

If you are concerned about the look of your laundry room. The look of your laundry room will remain elevated even if you place the sink beside the washer.

Another amazing advantage of installing the utility sink next to the washer can provide you with extra space. If your laundry room is small and you don’t have enough space.

You can adjust by placing both washer and sink side by side. Extra and additional pipelines can also spoil the outlook of your laundry room whereas you place both washer and sink side by side you use a single pipe link for both washers and sink by enhancing the overall look.

Is it important to call a plumber to install a utility sink and faucet?

No, it is not always important to call a plumber to install a sink or faucet. You can do all this work on your own.

Whenever you purchase a faucet, you will get an instructional manual that will help you in installing that specific faucet.

On the other hand, you can just google to find out a relevant answer to your question. Installing process is very easy and smiles just carefully reads the instruction gathers all the required tools and starts the installation process.

How much money do I have to pay to install the utility sink?

The overall amount of installing a utility sink depends upon the price of your sink and faucet. As there as both high and low-quality materials available in the market.

You can select any of them regarding your budget. Normal sink constructed by using vinyl and fiberglass can be of 50 to 100 $.

Whereas an elegant-looking sink made up of stainless steel or any other quality material can cost up to 180 – 500 $.

Well, besides the material there are several other factors that can increase the cost of the sink and faucet such as high-end brands and modern technological features.

Further, if you hire a professional plumber much more money will be added to your budget. A professional plumber can ask for almost 200 $ well the fee of a plumber varies from location to location.

But on the other hand, you can save a lot of expenses by yourself to proceed with the installation process.

What things we must consider in a utility sink for a washer?

The First and foremost thing to consider is its installation process. It must be easy to install. As there are numerous types of utility sinks that have different installation processes due to their different style.

Such as some are wall mounted, under mounter, drop in, or portable sinks. Besides being easy to install the style of utility sink also affect its long time durability.

While we are selecting a utility sink we want something that would work for a long time. First of all, check your area and then decide which style will go to your location.

The second thing to consider is the material used for its construction. You have options between cast iron, acrylic, ceramic, porcelain, and stainless.

The sink composed of stainless steel is light weighted and easy to clean. Next and the basic thing to consider is its size and depth.

As you know that How to install a utility sink next to the washer for washers is used to washcloths within them. You must select a perfect sink according to your workload.

If you have a huge work to perform with your sink a small sink could create a lot of problems. So you just need large size of the sink, with extra depth.

A sink with depth can help you with washing large items easily just like bed sheets various other things.


Install your utility sink and washers, water, and drain line with the same line. By using the same water supply line or drain line you can save a lot of space.

Further, the appearance of your launder room will automatically elevate. A lot of pipelines can spoil the overall look of your launder room.

This is the most efficient way of installing pipelines and a utility sink beside a washer. It will reflect a great difference over your water bill as well.

Leave a Comment